You are reading the article Samsung Galaxy S Blaze 4G Sgh updated in September 2023 on the website Climeeviet.com. We hope that the information we have shared is helpful to you. If you find the content interesting and meaningful, please share it with your friends and continue to follow and support us for the latest updates. Suggested October 2023 Samsung Galaxy S Blaze 4G Sgh
WARNING!
Warranty may be void of your device if you follow the procedures given on this page.
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
GUIDE: PHILZ TOUCH RECOVERY ON SAMSUNG GALAXY S BLAZE 4G SGH-T769Before you begin with guide instructions below, make sure your android device is adequately charged — at least 50% battery of the device.
STEP 0: CHECK DEVICE MODEL NO.To make sure your device is eligible with this, you must first confirm its model no. in ‘About device’ option under Settings. Another way to confirm model no. is by looking for it on the packaging box of your device. It must be SGH-T769!
Do not use the procedures discussed here on any other Galaxy S variants or any other device of Samsung or any other company. You have been warned!
STEP 1: BACKUP YOUR DEVICEBack up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on the internal memory, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
STEP 2: INSTALL LATEST DRIVERYou must have proper and working driver installed on your windows computer to be able to successfully flash PhilZ Touch Recovery on your Samsung Galaxy S Blaze. In case you’re not sure, follow the link below for a definitive guide for installing driver for your Galaxy S Blaze on your computer.
► SAMSUNG GALAXY S BLAZE 4G DRIVERS INSTALLATION GUIDE
STEP 3: INSTALLATION INSTRUCTIONS DOWNLOADSDownload the Odin zip file and PhilZ chúng tôi file given below. Transfer both Odin and recovery tar file to a separate folder on your computer just to keep things tidy.
ODIN ZIP FILE PHILZ TOUCH TAR FILEFor latest version of the ROM, check the original chúng tôi page →
STEP-BY-STEP GUIDEImportant Note: Backup important files stored on internal SD card of your device, so that in case a situation arises requiring you to do a factory reset after flashing PhilZ Touch Recovery, which might delete internal sd card too, your files will remain safe on PC.
Extract/Unzip the Odin zip file, Latest Odin3 v3.09.zip on your computer (using 7-zip free software, preferably) to get this file: Odin3 v3.09.exe
Move the PhilZ file, philz_touch_6.15.4-t769.tar.md5, in the same folder in which you extracted Latest Odin3 v3.09.zip (Just for your convenience, that is). So, now you’ll have the following files in that folder:
Odin3 v3.09.exe
philz_touch_6.15.4-t769.tar.md5
Disconnect the Galaxy S Blaze from PC if it is connected.
Boot your Samsung Galaxy S Blaze into Download Mode: (The image below of Galaxy S3 will help)
Power off your phone first and wait for 6-7 seconds after display is off
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home
If you don’t get the Added! message, here are some troubleshooting tips:
Make sure you have installed driver for Galaxy S Blaze as said above.
If you have already installed driver, then uninstall them and re-install back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot phone and PC and then try again.
Load the recovery file (Step 2) into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps.
PhilZ Touch Recovery has installed successfully on your S Blaze. To boot your Galaxy S Blaze into Recovery Mode:
Power off your phone first and wait for 6-7 seconds after display is off.
Press and hold these 3 buttons together: Volume Up + Power + Home.
If you see FAIL message instead of the PASS in Odin’s top left box, that’s a problem. Try this now: disconnect your Galaxy S Blaze from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 5 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your S Blaze from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 5 of this guide again.
FEEDBACK US!Your suggestions and queries, if any, are most welcomed!
You're reading Samsung Galaxy S Blaze 4G Sgh
Update the detailed information about Samsung Galaxy S Blaze 4G Sgh on the Climeeviet.com website. We hope the article's content will meet your needs, and we will regularly update the information to provide you with the fastest and most accurate information. Have a great day!